The Stream status / Go Live tab is the first stop before a show. It checks the path from camera to viewers, tells you what needs attention, and gives you the next useful button.
Open the play icon tab. The card is labelled Go Live.
The top card is a checklist. Work down it:
Start stream becomes available once the camera is ready and at least one destination is armed. It:
Overlays after the pre-roll (when the Overlays tab is on): a folded list in the checklist. Its title shows the overlays that will come on, so you can see your choice without opening it. Open it to tick or untick overlays; your choice is remembered for the next Start stream. Unticked overlays are left as they are. To change how an overlay looks, press Open Overlays. Until you pick, it uses whatever was showing when you last pressed Stop stream.
The card is either in start mode or stop mode, never both. Start mode shows the checklist, Start stream and Check again. Stop mode shows only You're live, Stop stream and, once you press it, the stop steps and their report until you press Done. Video still arriving after Stop (the camera, or your backup) does not count as live.
Use Stop stream to end the whole stream, play the ending and save a record of it. See Stop stream. Check again runs the checks now.
The pre-roll and the stream ending only play from Start stream and Stop stream on this tab. Go live and Stop in the Companion or the Director tab never play them.
On your phone: the Companion app's Go Live button opens the same checklist one step at a time: Camera, Where to stream, Get the video flowing, Before you start, then a summary with Start stream. It ends with You are streaming, Live chat and Back to home. Buttons are large enough for one thumb; the phone view leaves out this tab's status boxes. Start stream and Stop stream include the same pre-roll and ending. ✕ Close returns to the Companion without stopping the stream. While live, the button on every Companion phone reads 🔴 LIVE · End stream and opens Stop stream. See Companion app help. In a phone browser, add ?steps=1 to the Go Live page's address for the same view.
Step 3: Get the video flowing shows one short current activity or blocker. Connection details starts folded; open it for Camera / input, Encoder / director (or the direct relay), Bonded transport and Restreamer camera ingest evidence. Each stage says confirmed, blocked or not confirmed. Video reaching the router is not proof that the director is sending it or Restreamer receives it. Backup and standby pictures do not count as camera delivery. Read-only checks do not start publishing.
Known blockers also appear under Camera ready in the ordinary dashboard checklist. A direct relay or another encoder already delivering actual camera video does not require the absent Companion phone.
Starting a destination is not starting the encoder. Stream controls has one connection-progress line above the destinations. For Moto is not sending. Start video to continue., press Start video there; it sends the request in place, without reloading the same page. Destination error explanations are folded under Details. Destination enabled. only acknowledges a destination request, not video delivery. Any already-enabled destination may go public when the feed arrives; confirm deliberately, or stop destinations first to check only the private feed. No phone role is changed automatically.
Start video confirmation: when destinations may already be enabled, a confirmation appears on the page with Cancel and Start video. This works inside the Companion as well as a browser; it does not depend on browser pop-up dialogs. Cancel sends no command. Confirm sends one request and the same progress line follows it. A live camera preview alone is not outgoing video: the director can show the camera while sending nothing to the receiver.
Choose another director: if two or more eligible phones are online, Stream controls offers Director phone and Use as director. Select the intended phone, then confirm Use as director. The change can interrupt video. With the router camera relay, the cameras follow the new director; without it, their destinations may need changing. The status waits for the selected director to be confirmed. This is separate from Start video, and enabled destinations may publish when video arrives. Only online director/spare phones with Video enabled in Jobs are offered. Camera-only phones are not silently converted; use Make director on the Companion tab for that deliberate role change.
The Go Live card is always open. The other cards on the tab start folded to their titles the first time you open it on a device; tap a title to open one, and the dashboard remembers your choice.
The Stream opening & ending card on the Go Live tab brings the opening video and complete stream ending together. Pick optional videos from the Companion clip library (None turns a video off), choose the ending video's placement, then press Save.
Keep the dashboard and director's Companion app up to date for compatible ending controls and final-video error reporting.
Both need a Companion phone set up as the director (director mode). The Supporters and credits overlay can switch on by itself while either clip plays.
An end-roll video is optional: with None, only the enabled ordered sequence plays. Without an enabled timed sequence, the video plays alone, or with the ordinary supporters overlay if Play at the end of the stream is enabled. Video-last ordering is handled by the router for dashboard and Companion stops, not by a browser timer. Skip the stream ending skips the remaining ending and continues shutting down. Refresh-before-playback fetches the latest enabled URL lists before showing them and reports sources that had to use cached names.
Stop stream ends the stream everywhere, in the right order, and then saves everything about it to Past streams. The first tap only shows what it is about to do; nothing happens until you press Stop the stream. Cancel closes it.
It works through these steps one at a time, and only lists the ones your rig has:
The platforms go first, then the cameras, so viewers never see a frozen picture while a platform is still live.
Every stop is sent, even for things the dashboard thinks are already stopped. A status that is out of date must never leave something live, so Restream.io destinations, OBS, every Companion device and the DJI camera are all told to stop regardless.
The backup video comes back on by itself when you press Start stream (after the pre-roll, if you kept it off for the pre-roll), or as soon as a Restreamer destination is publishing again if you started some other way.
Each step turns green (done), red (did not work) or grey (nothing to do, or no way to tell), with a sentence saying what happened. A step that fails does not stop the others: a platform that would not switch off is no reason to leave a camera streaming. If a step went red, the heading says so (Stream stopped — 2 steps need you) and that part may still be live, so check it by hand.
Afterwards:
The Past streams card lists every stream the router noticed, newest first. Tap one for everything about it:
Download saves one stream's record as a file. Delete this stream removes one, and Clear all removes every saved stream; both ask first and cannot be undone.
You do not have to press Stop stream for a stream to be kept. The router notices by itself when a stream starts going out, a minute or two after the video starts, and a line under the Go Live buttons shows what it is counting (This stream: live 42 min · 1.9 GB sent so far · 318 chat messages). If you never press Stop stream, the stream is saved by itself half an hour after the video stops. A stream shorter than 3 minutes that ended by itself is not kept.
Good to know:
For Companion live-camera audio, Voice isolation is under Companion → encoder options, beside buffer and bitrate, and on the Restreamer tab with its presets and settings. It runs on the streaming server, not the phone, starts off, and its first switch-on reconnects the director once. Every paired phone's Camera section and Quick commands can switch it too.
The Your stream path card draws the chain the dashboard expects, before it runs live checks. It can include camera, encoder, this router, bond, receiver, OBS, Restreamer, Restream.io and platforms.
If a piece is missing, the card shows an item with a button to the right tab, such as Open bonding, Open Publishing or Open settings. Use those buttons first. The Go Live card keeps checking every few seconds and updates when the missing piece is fixed.
Use Change how this is set up → to open the guided setup wizard.
The checklist is built from the features you turned on. You will not see every line on every rig.
Video is coming in means at least one configured source is sending video or a publishing side is already live. The detail may name DJI camera, Companion is live, Companion input, router input, Director Mini, bond sending, OBS, Restreamer or Restream.io.
Measuring camera video means a DJI camera is on Wi-Fi and the dashboard is taking another traffic sample before calling it ready.
No video is coming in yet means the stream source has not started. Use the buttons shown for your sources, such as Director Mini, Companion cameras, DJI camera, SJCAM or Phone camera.
Director Mini is streaming means its active stream output is connected.
Director Mini needs a stream output means the Mini is reachable but not sending to a configured output. The checklist may show Start a destination buttons for the Mini's configured outputs. Press one, or open the Director Mini tab.
Director Mini is not reachable means the router cannot reach it. Check power, Wi-Fi or Ethernet, then start a scene and output.
Director Mini bypassed means Direct Camera mode is carrying the camera path instead.
Director Mini status unavailable means the router could not read the Mini's status. Open the Director tab and check the connection.
Bonding is running means the SRTLA sender is active.
Bonding is stopped is a hard blocker when SRTLA is your configured path. Press Start bonding.
No uplinks are currently admitted means the sender process is running but has no usable bonded source addresses. Open Bonding and admit or fix an uplink.
Bond status unavailable means the router could not read the bond status. Open Bonding.
Your bonding receiver is not answering means the sender can run, but the far-end receiver is not reachable. Check the receiver server, its public address, firewall and UDP port.
Cannot confirm the bonding receiver means the router could not prove the far end is healthy. Treat it as a warning and check the Bonding tab.
OBS checks run from your browser, not from the router. They describe whether this phone or laptop can reach OBS.
OBS is not answering is a warning, not always a blocker. OBS may be closed or on a network this device cannot see.
OBS needs its password is a blocker. Open Settings and fill the OBS WebSocket password from Tools → WebSocket Server Settings → Show Connect Info in OBS.
OBS is streaming means OBS is already publishing. The detail also says if it is recording.
OBS is connected but not streaming means OBS is reachable. If OBS is your publishing path, start streaming in OBS. If Restreamer or Restream.io publishes for you, you can ignore this.
Restreamer is publishing means at least one Restreamer destination is live. Use Stop stream when you are done.
Restreamer is ready means the stream path is ready, but no destination is live. Tick the destinations you want in the checklist and press Start stream.
Refreshing Restreamer status means the last answer was stale. Wait a moment or open Publishing.
Restreamer needs attention means the dashboard cannot reach or sign in to Restreamer, or Restreamer has a setup fault. Open Publishing and fix the setup card there.
Restream.io is live means Restream reports a live event. Open Restream.io to see destination switches and event state.
Restream.io is connected means you are signed in but Restream.io is not live yet. Point your encoder at the Restream stream key or finish the Restream.io route shown on its tab.
Restream.io is not connected means sign-in or API setup needs attention. Open Restream.io.
Start stream switches on the Restream.io channels you ticked in the checklist, and Stop stream switches them off. Restream.io itself goes live when your encoder sends it video.
If no Restreamer or Restream.io tab is configured, the checklist shows a warning. OBS can still publish by itself. Otherwise, open Settings and choose where the stream should go.
The Stream status tab icon carries a small dot:
The icon itself changes to a stop icon when the stream is live through the configured path.
The Start fresh for a new stream card resets per-stream counters and on-screen leftovers. It does not delete your settings, saved games, question bank, joke queue, overlay designs or prepared layouts.
Only features that are switched on are listed. The card can include:
| Item | What Reset all of these clears |
|---|---|
| GPS distance and steps | Distance and estimated steps. These also reset automatically when the dashboard sees a stream start. |
| Motion & g-force peaks | Peak g, airtime, spin, height change and steps on Companion phones that are reporting. This appears only when GPS, Companion, Motion & g-force and Pro are active. |
| Poll | The poll on air and its votes. Saved polls are kept. |
| Closest guess | The game on air, guesses and picture. Settings are kept. |
| Emoji meter | The meter on air and its counts. Your timing settings are kept. |
| Trivia points | The leaderboard. The running game and question bank are kept. |
| AI answer on screen | A What am I looking at? answer left on stream. Your answers stay on the Trivia tab for you. |
| Timer | Timer back to 0:00 and off screen. Timer design is kept. |
Press Reset all of these. The confirmation lists the exact items and says it cannot be undone.
Chat is separate on purpose. Clear chat messages clears messages shown so far from the Chat tab and chat overlay, takes down the Featured card and its queue, and empties Chat alerts. It does not delete anything on YouTube, Twitch, Restream.io or any other platform.
When you go live, the top card asks You're live. Start clean? and lists what would be cleared: the items above plus chat messages. Clear stats & messages resets them all at once (a timer that is running keeps running). Keep them closes the offer. It asks once per stream.
The automatic backup stream is configured on the Restreamer tab, in the Backup stream card. It needs a self-hosted Restreamer receiver. See Publishing for the Restreamer tab.
Upload one video. If the live feed stops, or its bitrate collapses far below normal, that video goes out to every platform Restreamer publishes to. It loops until your live feed is healthy again. Then the server switches back to live.
The decision runs on the streaming server, not on the router. That matters because the router is often the thing that lost signal.
On the Restreamer tab:
Uploading a video turns the feature on. A saved video can still be switched off, so check the status before you rely on it.
The upload is chunked so it works through the router's small PHP limits. The file can be up to 64 MB. The server prepares a stable holding clip, currently up to 1080p, 30 fps and 4000 kbps, even if your live stream is 4K.
The Head start for viewers section decides whether platforms sit behind live:
The card says Nothing to save. Changes store right away. There is no Save button.
A head start gives the server time to switch to the backup inside the buffered video, so viewers may never see a short dropout. The cost is chat delay. The line under the selector tells you what delay is actually in force and how much runway is left.
If you change the head start while live, it may wait for the next stream restart or backup switch before applying. Press Apply now only when you accept a short reconnect on every destination.
Open Fine tuning for the switching rules:
The fastest values do not make the switch instant. The server polls every couple of seconds, then platforms need time to accept the changed stream. The head start is what can hide that delay from viewers.
A switch keeps your destinations connected (receiver controller 1.4.3 and later). When the backup goes on, and again when it comes off, viewers see the picture freeze for a few seconds (5 to 11 in our tests) while the other source starts. The destinations stay connected, so Restream.io and YouTube do not end the broadcast or start a new one.
The Backup stream card says whether your channel switches this way. A few setups cannot yet: a stream that reaches the server over RTMP instead of SRT, a channel that converts the video, and sound that is missing or is not AAC stereo at 48 kHz, among others. There, each switch is still a short reconnect for every destination, once when the backup goes on and again when it comes off, and the card says why.
One more case (receiver controller 1.4.5 and later): the server prepares a copy of the backup video that matches your stream, and that takes about a minute after the receiver starts. If your stream drops before the copy is ready, the backup goes on air anyway, as the closest match it has. Going back to your stream then reconnects your destinations once, and while the backup is on, the card says so.
Either way, a connection that keeps dropping for a few seconds at a time makes a choppy stream. At a crowded venue, Come back after 20 seconds keeps the backup on through a flapping connection instead of switching back and forth. Where a switch still reconnects, 5 seconds turns every blip into two reconnects.
You do not need Restream.io's paid Disconnect Protection. Covering a dropout is what the backup stream is for, and it keeps your destinations connected while it does. If the WiFi, repeater & radios box at the top of the Router tab is red, press Fix it for me before you go live.
Press Try it now to force the backup video on air. This is a real test: viewers will see the backup.
The button becomes Stop the test. The test also stops after about a minute, and saving any backup setting clears the forced backup. The dashboard waits for the controller to confirm before saying the backup is on air.
The Backup stream card keeps a Last 24 hours block. It records real outages, not just switches. A dropout that happened before a backup video was uploaded still appears, because that is exactly the problem the backup is meant to solve.
The Restreamer tab icon can warn about recent backup trouble: